Demountable Lining System

Introducing our patented lift-off panel mounting solution, specifically designed to enable the low-cost installation of easily demountable internal architectural finishes.

XFrame's DLS 010 clip system is designed to make the installation of demountable architectural wall finishes time and cost-efficient. Made from 100% recycled nylon, the clip takes advantage of a hidden key-hole milled into the rear of linings to achieve a strong yet easily reversible panel connection. The 010 clip is a singled-sided design for fast on-site installation and the keyhole design is self-aligning to ensure precision panel seams.

Available to purchase now. Contact XFrame for samples. MOQs apply.

XFrame DLS 010 Specification (.pdf)

Download

XFrame DLS 010 CAD for Clip Only (.dxf)

Download

XFrame DLS 010 3D Model (.3dm)

Download

XFrame DLS 010 CAD for Typical Sheet (.dxf)

Download

XFrame DLS 010 Typical Clip Spacing (.pdf)

Download

Single Sided Design

Increased factory and on-site productivity though a single-part system.

No Protruding Panel Hardware

Slot milling in the rear of lining panels means stacked sheets, and panels in transit, are less likely to become damaged.

Self Centering

The key-hole shaped hole in lining panels, and the rounded design of the clip, ensures precision alignment.

Engineered for Strength

A single solid nylon injection molded part with 3mm walls and lead-in chamfers makes the 010 system suitable for heavy panel mounting.

Adjustable Lift-Off

Use of a grooved receptacle make it possible to adjust the panels lift-off height depending on job specific requirements.

Options for Flush-mount

Set demountable panels hard on structural frames and substrates for improved acoustics and alignment.

XF010 - Flush

Design: 1-Part (Male) with CNC female - lift-off fixing.
Fixing Method: Screws - one long into frame (typically 40mm 8g CS chip-board screw).
Offset: Flush specification - no gap - lining hard against wall frame. Only works for 16mm or deeper linings.
CAD/CAM Requirements - Lining Side: XF010 CAM Flush Geometry.
CAD/CAM Requirements - Frame Side: A single 3mm dia. pilot hole for clip screw.
Spacing: Max. 600mm centers between clips both horizontally and vertically.
Load Capacity: 30kg per clip.
Usage: For 16mm (5/8 inch) linings. Suitable when the wall thickness needs to be minimised.

XF010 - Typical

Design: 1-Part (Male) with CNC female - lift-off fixing.
Fixing Method: Screws - one long into frame (typically 40mm 8g CS chip-board screw).
Offset: 4mm gap between wall frame and back of linings.
CAD/CAM Requirements - Lining Side: XF010 CAM Typical Geometry.
CAD/CAM Requirements - Frame Side: A single 3mm dia. pilot hole for clip screw.
Spacing: Max. 600mm centers between clips both horizontally and vertically.
Load Capacity: 30kg per clip.
Usage: For any lining 12mm or deeper - allows linings to be easily hung and removed.

XF010 - Rail

Design: 1-Part (Male) with CNC female - lift-off fixing.
Fixing Method: Screws - one long into frame (typically 40mm 8g CS chip-board screw).
Offset: 4mm gap between wall frame and back of linings.
CAD/CAM Requirements - Lining Side: XF010 CAM Rail Geometry.
CAD/CAM Requirements - Frame Side: A single 3mm dia. pilot hole for clip screw.
Spacing: Max. 600mm centers between clips both horizontally and vertically.
Load Capacity: 30kg per clip.
Usage: For any lining 12mm or deeper - allows linings to be easily hung and removed. Allows linings horozontial location to be adjusted on site via a sliding connection.

Built for CAD/CAM Production

The XFrame DLS 010 system has been designed to work with best-in-class Amana Tool 48100 milling T-Slot tools. The 48100 creates a 4mm~ slotted profile and is compatible with most flat-bed CNC milling equipment. The tool permits up to an 8mm wide slot-to-shank clearance which boosts the 010 systems strength when hanging thin sheet materials (minimum support sheet thickness of 12mm / 1/2 inch).